Mogami 3082 NEGLEX OFC Co-Axial Speaker Cable (terminated pair)

Key Features: Mogami 3082 NEGLEX OFC Co-Axial Speaker Cable (Terminated Pair)

Coaxial speaker cable design
Utilises a coaxial conductor layout (central conductor + outer conductor/shield) made from oxygen-free copper (OFC), providing a stable signal path and efficient power delivery to speakers.

Adequate conductor cross-section
The conductor size is suitable for typical speakers and amplifiers — offering a balance between flexibility and sufficient current capacity for small- to medium-power systems.

Low resistance for good power transfer
The cable’s construction supports efficient transfer of amplifier output to speakers with minimal loss, helping maintain sound quality, bass, and dynamics.

Terminated pair — ready to use
Sold as a matched pair of terminated speaker cables (ready for hooking up to amplifier and speakers), saving you the effort of cutting and terminating from bulk wire.

Flexible, manageable cable build
The cable remains reasonably flexible and manageable, making it easier to route behind equipment, under furniture, or along walls compared to bulky, heavy-duty cables.

Good for stereo, hi-fi, small-to-mid power setups
Suited for bookshelf speakers, floor-standing speakers for moderate power, or compact home-audio/hi-fi systems where heavy gauge cabling isn’t required.

Balanced trade-off: performance vs convenience
By offering a pre-terminated cable with decent quality copper and coaxial design, it strikes a middle ground — better than basic speaker cables bundled with speakers, but without the bulk or cost of high-end heavy-gauge cables.

Description

- Mogami is by far the world’s most sought-after studio cable brand; most major recording studios and leading sound engineers in the world use Mogami cabling due to the legendary performance of these cables. You are buying the best when you buy Mogami. All Mogami cables are made in Japan using the best materials and technological know-how that comes from decades of research and development.
- All our custom-made cables are professionally soldered with a Proprietary 4% Silver solder blend.
- Mogami 3082 features a coaxial design (shield and central conductor) to provide a large conductor size to optimise noise rejection and to minimise the possibility of emission of noise to the surroundings (due to induction). This coaxial design offers better quality signal transmission compared to standard Figure-8 and Twisted-Pair speaker cable. The shield, as well as the centre conductor, is 2mm square each (between 14 and 15 AWG), Mogami has managed to make the 3082 cable ultra-flexible and keep the overall diameter at 6.5mm, despite the large conductor size.
- Hooking up your home audio system will be a breeze with these cables.
  
  Mogami 3082 NEGLEX OFC Co-Axial Speaker Cable
  
  The Mogami 3082 NEGLEX OFC Co-Axial Speaker Cable is a Stereo Audiophile terminated version (2.5 m and 3.0 pair ) sold as a terminated pair with banana plugs.
  
  This is a Professional studio monitoring and high-end recording cable with a coaxial construction.
  Manufactured in Japan using Neglex OFC copper of size 2.0mm² ( #14AWG), this Speaker Cable is designed to mate with XLR/TS and SpeakOn Connectors
  Due to its construction and orientation, the 3082 offers a more dynamic representation than conventional cables.
Features of the Mogami 3082 NEGLEX OFC Co-Axial Speaker Cable
- Large conductor size of 2.0mm (close to #14AWG) despite a small OD of 6.5mm (0.256″). (Same conductor size for both internal and external (shield) conductors.)
- Extremely low induction from outside and affection to outside.
- Neglex copper ofc conductors
Testimonial
“I was stunned by how dramatically the coaxial 3082 speaker cable affected the sound of my NS-10Ms. I was using good wire before, but the improvement the 3082 made was not subtle. The speakers sounded noticeably louder, and the response was more natural and extended. I had no idea speaker cable could be so significant. Thanks so much for a great solution and
a wonderful improvement on my monitoring!”

Note –
To use in conventional 2-core mode with a banana plug, the coax cable must be stripped with the outer layer forming one core ( black ) and the inner centre forming the second core.
Heatshrink needs to be used to insulate each core.